| FOX Matrix 14400 |
| NOTE | The I/O cards are class 1 laser products. They meet the safety regulations of IEC-60825, FDA 21 CFR 1040.10, and FDA 21 CFR 1040.11. |
|
| NOTE | The FOX 3G I/O SM P and FOX I/O 1616 HD-SDI boards offer immunity to "pathological" signals, including test patterns defined by SMPTE Recommended Practice (RP) 178 and SMPTE RP 198 for SD-SDI, HD-SDI, and 3G-SDI. |
|
| NOTE | FOX 3G I/O SM P boards are immune to pathological signals only when used with P model transmitter and receiver units with no other equipment between the transmitter, board, and receiver units. |
|
|
| Optical specifications |
|---|
| Number/type | 16 singlemode or 16 multimode fiber optic inputs and outputs (16 Tx and 16 Rx) per I/O board |
| NOTE | Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit return data for bidirectional control/communication. |
|
| Connectors | 32 LC connectors per I/O board |
| Operating distance | |
| Singlemode | 30 km (18.75 miles) with singlemode (SM) cables with an Extron singlemode distribution amplifier or transmitter/receiver |
| Multimode | 300 m (985') with 62.5 µm OM1 multimode (MM) cables with an Extron multimode Tx/Rx unit
1 km (3280') with 50 µm OM2 multimode (MM) cables with an Extron multimode Tx/Rx unit
2 km (6561') with 50 µm, OM3/OM4, 2000 MHz bandwidth, laser-optimized multimode (MM) cables with an Extron multimode Tx/Rx unit |
| NOTE | Operating distance is approximate. These are typical distances. The maximum distance may be greater than these typical numbers depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. |
|
| Nominal peak wavelength | 850 nm for multimode (MM), 1310 nm for singlemode (SM) |
| Transmission power | |
| Singlemode | -5 dBm, typical |
| Multimode | -5 dBm, typical |
| Maximum receiver sensitivity | |
| Singlemode | -18 dBm, typical |
| Multimode | -12 dBm, typical |
| Optical loss budget | |
| Singlemode | 13 dB, maximum |
| Multimode | 7 dB, maximum |
| Maximum channel data rate | 4.25 Gbps |
|
| Video |
|---|
| Routing | 16 x 16 up to 144 x 144 unidirectional (Tx) matrix or
8 x 8 up to 72 x 72 bidirectional (Tx/Rx) matrix |
| Gain | Unity |
| Pixel data bit depth | 8 bits per channel, 3 channels (R, G, B) |
|
| Video/audio input or output |
|---|
| Number/signal type | 16 to 144 fiber optic signals |
| Connectors | 16 LC connectors per I/O board |
| Re-clocking | 2.125 Gbps, 4.25 Gbps, bypass, or automatic (SM P boards only) |
| NOTE | Input comes from an Extron fiber optic transmitter, fiber optic distribution amplifier, or fiber optic matrix switcher. |
|
| NOTE | Output connects to an Extron fiber optic receiver. |
|
|
| Digital video — SDI/HD-SDI/3G-SDI (FOX 14400 Series with FOX I/O HD-SDI) |
|---|
| Routing | |
| FOX I/O 1616 HD-SDI | 16 x 16 up to 144 x 144 matrix |
| Gain | Unity |
| Maximum data rate | 2.97 Gbps |
| Auto data rate lock | Yes |
| Data types | 8 or 10 bit |
| Operation standards | SMPTE 292M, SMPTE 259M, SMPTE 297-2006, SMPTE 424M, ITU-RBT.601, ITU-RBT.1120 |
|
| Digital video input — SDI/HD-SDI/3G-SDI (FOX 14400 Series with FOX I/O HD-SDI) |
|---|
| Number/signal type | 16 single link SDI, HD-SDI, or 3G-SDI; or 8 dual link HD-SDI per board |
| Connectors | 16 female BNC per board |
| Nominal level | 0.80 Vp-p ±10% |
| Impedance | 75 ohms |
| Return loss | >13 dB @ 1 MHz to 1.3 GHz |
| Equalization | Automatic |
| Input cable equalization distance with FOX I/O 1616 HD-SDI boards | |
| 3G-SDI | |
| Extron RG6, Belden 1694A cable | 410' (125 m) |
| Extron R59, Belden 1505A cable | 350' (107 m) |
| HD-SDI | |
| Extron RG6, Belden 1694A cable | 650' (198 m) |
| Extron R59, Belden 1505A cable | 550' (168 m) |
| SDI | |
| Extron RG6, Belden 1694A cable | 1230' (357 m) |
| Extron R59, Belden 1505A cable | 1100' (335 m) |
| NOTE | The transmission distance varies depending on the signal resolution and on the type of cable, graphics card, and display used in the system. |
|
|
| Digital video output — SDI/HD-SDI/3G-SDI (FOX 14400 Series with FOX I/O HD-SDI) |
|---|
| Number/signal type | 16 single link SDI, HD-SDI, or 3G-SDI; or 8 dual link HD-SDI per board |
| Connectors | 16 female BNC per board |
| Nominal level | 0.80 Vp-p ±10% |
| Impedance | 75 ohms |
| Return loss | >11 dB @ 1 MHz to 1.3 GHz |
| DC offset | 0 V with input at 0 offset |
| Re-clocking | Automatic, or use available bypass mode for nonstandard rates |
| Jitter | <0.2 UI |
| Rise and fall time (20-80%) | 600 ps ±200 ps |
|
| Control/remote — switcher |
|---|
| Serial control port | 1 bidirectional RS-232 or RS-422, female 9-pin D connector (rear panel)
1 bidirectional RS-232, 2.5 mm mini stereo jack (front panel ) |
| Baud rate and protocol | 9600 to 115200 baud, 9600 baud (default), 8 data bits, 1 stop bit, no parity |
| Serial control pin configurations |
| 9-pin female D connector | RS-232: 2 = Tx, 3 = Rx, 5 = GND
RS-422: 2 = Tx-, 3 = Rx-, 5 = GND, 7 = Rx+, 8 = Tx+ |
| Mini stereo jack | RS-232: tip = Tx, ring = Rx, sleeve = GND |
| Ethernet control port | 1 female RJ-45 connector |
| Ethernet data rate | 10/100Base-T, half/full duplex with autodetect |
| Ethernet protocol | ARP, ICMP (ping), IP, TCP, UDP, DHCP, HTTP, SMTP, SNMP, Telnet |
| Default settings | Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Gateway = 0.0.0.0
DHCP = off |
| Web server | Up to 200 simultaneous sessions
7 MB nonvolatile user memory |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS™)
Microsoft® Internet Explorer® ver. 6 or higher, Telnet |
|
| General |
|---|
| Power supply | Internal, 2* (positive-negative), primary and redundant, hot-swappable
Input: 100-240 VAC, 50-60 Hz
*A redundant power supply is standard. |
| Power consumption | Enclosure without boards: 50.9 watts
Enclosure fully loaded with 9 MM boards: 250 watts
Enclosure fully loaded with 9 SM reclocking boards: 269 watts
Enclosure fully loaded with 9 FOX I/O 1616 HD-SDI boards: 296 watts
Each MM board: 22.1 watts
Each SM board: 24.2 watts
Each SDI/HD-SDI board: 27.2 watts |
| Ambient temperature/humidity | |
| FOX I/O 1616 HD-SDI | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +104 °F (0 to +40 °C) / 10% to 90%, noncondensing |
| All other boards and models | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Fan, right to left (as viewed from front panel) |
| Thermal dissipation, full load | 1011 BTU/hr |
| Mounting | |
| Rack mount | Yes |
| Enclosure type | Metal |
| Enclosure dimensions | 14.0" H x 17.0" W x 12.25" D (8U high, full rack wide)
(35.6 cm H x 43.1 cm W x 31.1 cm D)
(Depth excludes connectors and handles. Width excludes rack ears.) |
| Product weight (fully loaded) | 69.1 lbs (31.3 kg) |
| Shipping weight | 75 lbs (34 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (8.0-032113-D11) |