| HC 402 EU/MK (HCT 101 EU/MK, HCR 102) |
| NOTE | This product consists of a switching transmitter (HCT 101 EU or HCT 101 MK) and a scaling receiver (HCR 102), sold together as a system. |
|
|
| Video input |
|---|
| Number/signal type | |
| Digital | |
| HCT 101 EU, HCT 101 MK | 1 HDMI (or single link DVI-D with the appropriate DVI-HDMI adapter) |
| HCR 102 | 1 HDMI (or single link DVI-D with the appropriate DVI-HDMI adapter) |
| Connectors | |
| HCT 101 EU, HCT 101 MK | 1 female HDMI type A |
| HCR 102 | 1 female HDMI type A |
| HDMI equalization | Automatic |
| HDMI input cable length | ≤50' (15 m) for resolutions up to 1920x1200 or 1080p @ 60 Hz; 2K, using Extron HDMI Pro Series cable |
| Resolution range | 640x480 to 1600x1200 and 1920x1200*, 480p, 576p, 720p, 1080i, 1080p, and 2K
*reduced blanking |
| Return loss | <-30 dB @ 5 MHz |
| DC offset (max. allowable) | 250 mV |
| Standards | DVI 1.0, HDMI 1.4, HDCP 1.4 |
|
| Interconnection between transmitter and receiver |
|---|
| Connector | 1 female RJ-45 on each unit (transmitter and receiver) |
| Termination standard | TIA/EIA T568B |
| Transmission distance | Up to 230' (70 m) using shielded twisted pair (STP) cable or XTP DTP 24 STP cable with a 1080p, 60 Hz signal |
| Cable requirements | Solid conductor, 24 AWG or better |
| Cable recommendations | 400 MHz bandwidth, STP (shielded twisted pair) |
| NOTE | Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. |
|
|
| Video processing |
|---|
| Decoder | 12 bit digital (3D-adaptive comb filter) |
| Digital pixel data bit depth | 8, 10, or 12 bits per channel; 165 MHz pixel clock |
| Colors | 1 billion (10 bit processing) |
|
| Video output |
|---|
| Number/signal type | 1 HDMI (with CEC) |
| Connectors | 1 female HDMI |
| HDMI peripheral device power | 250 mA |
| Scaled resolution | 640x4806,8,9, 800x6006,8,9, 852x4806,8,9, 1024x7686,8,9, 1024x8526,8,9, 1024x10246,8,9, 1280x7686,8,9, 1280x8006,8,9, 1280x10246,8,9, 1360x7656,8,9, 1360x7686,8,9, 1365x7686,8,9, 1365x10246,8,9, 1366x7686,8,9, 1400x10506,8, 1440x9006,8,9, 1600x9006,8, 1600x12006,8, 1680x10506,8, 1920x12006,8
HDTV 480p7,8, 576p6, 720p3,4,5,6,7,8, 1080i6,7,8, 1080p1,2,3,4,5,6,7,8, 2048x10801,2,3,4,5,6,7,8
1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz,4 = at 29.97 Hz, 5 = at 30 Hz, 6 = at 50 Hz, 7 = at 59.94 Hz, 8 = at 60 Hz, 9 = at 75 Hz |
|
| Audio |
|---|
| Gain | Unbalanced output: 0 dB; balanced output +6 dB |
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise | <0.1%, 20 Hz to 20k Hz at nominal level |
| S/N | >90 dB, at maximum input (unweighted) |
| Crosstalk | ≤-80 dB @ 1 kHz, fully loaded |
| Stereo channel separation | >80 dB @ 1 kHz |
|
| Audio input |
|---|
| Number/signal type | 2 digital audio, embedded in the HDMI signal |
| Connectors | 2 female HDMI Type A |
| Source formats | |
| HDMI | LPCM up to 7.1/24-bit/192 kHz, Dolby TrueHD, Dolby Digital Plus, Dolby Digital EX, Dolby Digital 5.1, Dolby Digital 2/0 Surround, Dolby Digital 2/0, DTS-HD Master Audio, DTS-HD, DTS-ES Discrete 6.1, DTS-ES Matrix 6.1, DTS Digital Surround 5.1, DTS 2 Channel |
| Impedance | 10k ohms, DC coupled |
| Nominal level | -10 dBV, unbalanced |
| Maximum level | +6 dBV, unbalanced |
| CMRR | >60 dB typical, unbalanced, @ 1 kHz |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output |
|---|
| Number/signal type | 1 analog, line level stereo, balanced or unbalanced (variable)
1 digital, embedded in HDMI (fixed) |
| Connectors | (1) 3.5 mm captive screw connector, 5 pole
1 female HDMI |
| Impedance | 50 ohms unbalanced, 100 ohms balanced |
| Gain error | ±0.5 dB channel to channel |
| Maximum level (Hi-Z) | >+15 dBu, balanced; >+9 dBu, unbalanced |
| Output volume range | 0 to 100% in 1% steps |
|
| Communications |
|---|
| USB control port | 1 receiver front panel female USB mini-B |
| USB standards | USB 2.0, high speed |
| Program control | Extron Product Configuration Software (PCS) for Windows® |
|
| Communications — control processor |
|---|
| Memory | |
| SDRAM | 512 MB |
| Flash | 512 MB |
| Software | |
| Configuration software | Extron Global Configurator® Plus and Professional |
| Utilities | Toolbelt, embedded web page |
| Ethernet | |
| Network interface controllers (NICs) | 1 |
| Connectors | 1 female RJ-45 connector |
| Data rate | 10/100Base-T, half/full duplex with autodetect |
| Protocols | DHCP, DNS, HTTP, HTTPS, ICMP, IEEE 802.1X, NTP, SFTP, SMTP, SNMP, SSH, TCP/IP, UDP/IP |
| Default settings | Link speed and duplex level = autodetected
IP address = 192.168.254.250
Subnet mask = 255.255.255.0
Gateway = 0.0.0.0
DHCP = off
DNS: 127.0.0.1 |
| Serial | |
| Quantity/type | 1 bidirectional RS-232 |
| Connectors | (1) 3.5 mm captive screw connector, 3-pole |
| Baud rate and protocol | 300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits;
1 (default) or 2 stop bits;
no parity (default), even, or odd parity |
| NOTE | This 3-pole port supports software flow control. The default is no flow control.
|
|
| Pin configuration | Pin 1 = Tx, 2 = Rx, 3 = Gnd |
| Digital I/O | |
| Quantity/type | 4 digital input/output (configurable) |
| Connectors | (1) 3.5 mm captive screw connector, 6-pole |
| Digital inputs | |
| Input voltage range | 0 to 24 VDC, clamped at +30 VDC |
| Input impedance | >10k ohms |
| Programmable pullup | 1k ohms to +5 VDC |
| Threshold low to high | 2.8 VDC |
| Threshold high to low | 2.0 VDC |
| Digital outputs | 250 mA sink from 24 VDC max. |
| Pin configurations | Pins 1, 2, 4, 5 = digital I/Os 1, 2, 3, 4; pins 3, 6= Gnd |
| IR | |
| Quantity/type | 1 programmable TTL level (0 to 5 V) infrared (carrier and non-carrier) up to 300 kHz |
| Connector | (1) 3.5 mm captive screw connector, 2-pole |
| Pin configuration | Pin 1 = signal, 2 = Gnd |
| IR output carrier frequency | 30 kHz to 300 kHz |
|
| General |
|---|
| Power supply | External, included
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 4.2 A, 50 watts |
| Power consumption | |
| System | |
| Device | 16.8 watts |
| Device and power supply | 19.0 watts |
| NOTE | Connect the included 4.2 A, 50 W, external power supply to the HCR 102, and the receiver remotely powers the HCT 101 EU or HCT 101 MK. Alternatively, the transmitter can be powered locally by an optional external power supply. |
|
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +104 °F (0 to +40 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on top and sides |
| Thermal dissipation | |
| System | |
| Device | 56.4 BTU/hour |
| Device and power supply | 65.9 BTU/hour |
| Mounting | |
| HCT 101 EU | |
| Furniture or wall mount | Yes, with an EU 1-gang electrical junction box and included EU 1-gang frame |
| HCT 101 MK | |
| Furniture or wall mount | Yes, with an MK 1-gang electrical junction box and included MK 1-gang frame |
| HCR 102 | |
| Rack mount | Yes, with optional 1U high rack shelf or back of the rack mounting kit |
| Furniture mount | Yes, with included, attached MBU 125 under-desk mounting brackets |
| Enclosure type | Metal |
| Enclosure dimensions | |
| HCT 101 EU | |
| Frame | 3.17" H x 3.17" W x 0.40" D (1-gang)
(81 mm H x 81 mm W x 10 mm D) |
| Device | 2.17" H x 2.17" W x 1.60" D
(55 mm H x 55 mm W x 41 mm D)
(Excludes faceplate. Fits mounting frames that accept 55 mm x 55 mm modules and fits many 1 gang EU junction boxes. Allow at least 2.4" [61 mm] depth in the wall or furniture.) |
| |  |
| HCT 101 MK | |
| Frame | 3.39" H x 3.39" W x 0.40" D (1-gang)
(86 mm H x 86 mm W x 10 mm D) |
| Device | 2.17" H x 2.17" W x 1.60" D
(55 mm H x 55 mm W x 41 mm D)
(Excludes faceplate. Fits mounting frames that accept 55 mm x 55 mm modules and fits many 1 gang EU junction boxes. Allow at least 2.4" [61 mm] depth in the wall or furniture.) |
| |  |
| HCR 102 | 1.0" H x 8.75" W x 6.0" D (half rack wide)
(25 mm H x 222 mm W x 152 mm D)
(Depth excludes connectors.) |
| Product weight | |
| HCT 101 EU, HCT 101 MK | 0.2 lb (0.1 kg) |
| HCR 102 | 1.2 lbs (0.6 kg) |
| Regulatory compliance | CE**, C-tick, c-UL, FCC Class A**, ICES, UL, VCCI
Complies with the appropriate requirements of RoHS, WEEE |
| NOTE | **CE and FCC testing is conducted with STP (shielded twisted pair) I/O cable. |
|
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (5467-D2) |