| PVS 305SA IP |
|
| Video |
|---|
| Gain | Unity (as a system including Extron PVT Series wallplates) |
| Bandwidth | |
| RGB | 200 MHz (-3 dB) @ 50' (15 m) of cable |
| Composite video | 100 MHz (-3 dB) |
| Differential phase error | Composite video: 0.25° at 3.58 MHz and 4.43 MHz |
| Differential gain error | Composite video: 0.15% at 3.58 MHz and 4.43 MHz |
| Crosstalk | -70 dB @ 5 MHz |
| Switching speed | 1 ms (max.) from front panel, 1-2 s from remote panel |
| CMRR | -90 dB @ 100 Hz, -70 dB @ 10 MHz |
|
| Video input |
|---|
| Number/signal type | Inputs 1 and 2: VGA-UXGA RGBHV, RGBS
Inputs 3 and 4 (configurable): VGA-UXGA RGBHV, RGBS, or composite video |
| Connectors | 4 pairs female RJ-45 |
| Nominal level | As a system including Extron PVT Series wallplates:
1 Vp-p for composite video (including sync)
0.7 Vp-p for RGB |
| Minimum/maximum levels | Analog (as a system including Extron PVT Series wallplates) |
| RGB | 0.3 V to 1.5 Vp-p with no offset |
| Composite video | 0.4 V to 2.0 Vp-p with no offset |
| Impedance | 75 ohms (as a system including Extron PVT Series wallplates) |
| Horizontal frequency | 15 kHz to 145 kHz |
| Vertical frequency | 30 Hz to 170 Hz |
| Return loss | Composite video: <-40 dB @ 5 MHz |
| DC offset (max. allowable) | 1.0 V |
|
| Video output |
|---|
| Number/signal type | 1 VGA-UXGA RGBHV, RGBS (follows input type)
1 composite video |
| Connectors | 1 female 15-pin HD
1 female RCA |
| Nominal level | As a system including Extron PVT Series wallplates:
1 Vp-p for composite video (including sync)
0.7 Vp-p for RGB |
| Minimum/maximum levels | |
| RGB | 0.3 V to 1.5 Vp-p (follows input) |
| Composite video | 0.4 V to 2.0 Vp-p (follows input) |
| Impedance | 75 ohms |
| Return loss | <-40 dB @ 5 MHz |
| DC offset | |
| RGB | ±5 mV, max., with input at 0 offset |
| Composite video | ±20.5 mV with input at 0 offset |
|
| Sync |
|---|
| Input type | RGBHV, RGBS (RGB input) |
| Output type | RGBHV, RGBS (RGB output, follows input) |
| Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM (for composite video inputs and output) |
| Input level | 2.0 V to 5.5 Vp-p |
| Output level | 4.5 V to 5.5 Vp-p, unterminated |
| Input impedance | 510 ohms |
| Output impedance | 75 ohms |
| Max. propagation delay | 40 ns (system only, not due to cable delay) |
| Max. rise/fall time | 15 ns |
| Polarity | Positive or negative (follows input) |
|
| Audio input — refer to the PVT Series Wallplates' audio specifications |
|---|
| Number/signal type | 4 proprietary signals from Extron PVT Series wallplates
1 stereo, balanced/unbalanced (input 5) |
| Connectors | 4 female RJ-45 (2 shared with RGB inputs, 2 shared with configurable RGB/composite video inputs)
1 female 3.5 mm captive screw connector, 5 pole (input 5) |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio — preamplifier |
|---|
| Input gain adjustment | –18 dB to +24 dB (default = 0 dB), adjustable per input via RS-232 |
| Input level sensitivity | -10 dBV (0.316 Vrms) for maximum output before clipping |
| Volume control range | 0 to -61 dB |
| Crosstalk | <-85 dB @ 1 kHz (as a system with Extron PVT Series wallplates with 50' cables) |
| Stereo channel separation | >80 dB @ 1 kHz (as a system with Extron PVT Series wallplates with 50' cables) |
| Bass adjustment | ±10.5 dB @ 50 Hz |
| Treble adjustment | ±10.5 dB @ 15 Hz |
|
| Audio input — VoiceLift™ receiver |
|---|
| Number/signal type | 2 mono, balanced (mic and aux) |
| Connectors | 1 female RJ-45 |
| Impedance | >10k ohms unbalanced/balanced, DC coupled |
| Nominal level | -10 dBV (316 mVrms) |
| Input gain/volume adjustment | -18 dB to +24 dB (default = 0 dB), adjustable independently from all other audio gain and volume controls via front panel or RS-232 |
| Input level sensitivity | -10 dBV (316 mVrms) for maximum output before clipping when VoiceLift Receiver volume is set to 24) |
|
| Audio output — lineout |
|---|
| Number/signal type | 1 stereo/mono, balanced/unbalanced, fixed/variable |
| Connector | (1) 3.5 mm captive screw connector, 5 pole |
| Impedance | 50 ohms unbalanced, 100 ohms balanced |
| Gain error | ±0.8 dB channel to channel |
| Maximum level (600 ohms) | +8 dBu, balanced, at <0.1% THD+N |
| NOTE | Unbalanced wired outputs produce 6 dB of attenuation. Balanced output has unity gain/attenuation. |
|
|
| Audio output — power amplifier |
|---|
| Number/signal type | 1 stereo or 2 mono (default), 2 channels total |
| Connectors | (1) 5.0 mm captive screw connector, 4 pole |
| Load impedance | 2 ohms, minimum |
| Amplifier type | Class D |
| Gain/volume adjustment | -10 dB to +10 dB (default = 0 dB), adjustable in 1 dB steps |
| Frequency response | 20 Hz to 20 kHz, -1 dB/+3.5 dB @ 1 watt output, 8 ohm load |
| THD + Noise | 0.2% @ 1 kHz at nominal level (1 watt, 8 ohm load) |
| S/N | >67 dB, 20 Hz to 20 kHz at maximum output (unweighted), 8 ohms (as a system with Extron PVT Series wallplates with 50' cables) |
| Output power | 25 watts rms per channel, 2/4/8 ohms, 1 kHz, 1% THD |
| Damping factor | >75 @ 8 ohms |
|
| Control/remote — switcher |
|---|
| Serial host control ports | 2 bidirectional RS-232: 1 rear panel 3.5 mm captive screw connector, 5 pole (shared with IR control); 1 front panel 2.5 mm stereo mini jack |
| Baud rate and protocol | 9600 baud, 8 data bits, 1 stop bit, no parity |
| Serial control pin configurations | Captive screw connector: A = Tx, B = Rx, C = IR receive, D = GND, E = 12 VDC
2.5 mm mini stereo jack: tip = Tx, ring = Rx, sleeve = GND |
| DC volume control port | (1) 3.5 mm captive screw connector, 3 pole |
| DC volume control pin configurations | 1 = +10 VDC, 2 = volume/mute (variable voltage), 3 = GND |
| Volume control voltage range | 0 V (mute) to 10 V (maximum volume) |
| Paging sensor connector | (1) 3.5 mm captive screw connector, 2 pole |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS™) |
|
| Ethernet control interface |
|---|
| Switch type | Unmanaged |
| Standards | IEEE 802.3, IEEE 802.3u, IEEE 802.3x |
| Recommended cable type | For 10Base-T: UTP CAT 3 or better
For 100Base-TX: UTP CAT 5 or better |
| Ethernet ports | 4 female RJ-45 with built-in link/speed and activity LEDs |
| Ethernet data rate | 10/100Base-T (10/100 Mbps) with autodetect |
| MAC address table | 1 k |
| Buffer | 64 kB |
| Switching method | Store and forward |
| MDI/MDI-X selection | Automatic |
| PoE | Not supported |
| SNMP | Not supported |
| QoS | No |
| LACP | Not supported |
| Layer | 2 |
| Port mirroring | Not supported |
| VLAN | Not supported |
|
| General |
|---|
| Power | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 5 A, 60 watts |
| Power consumption | 10.0 watts |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on sides |
| Thermal dissipation | 34.1 BTU/hr |
| Mounting | |
| Furniture mount | Yes, with optional mini under-desk mounting kit |
| Pole mount | Yes, with optional pole mounting kit |
| Enclosure type | Metal |
| Enclosure dimensions | 1.8" H x 10.1" W x 3.0" D
(4.5 cm H x 25.7 cm W x 7.6 cm D) |
| Product weight | 2.5 lbs (1.1 kg), plus power supply (0.9 lbs [0.4 kg]) |
| Shipping weight | 5 lbs (2.3 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL
UL rated for use in plenum airspaces: meets UL 2043 for heat and smoke release, excluding the power supply; meets UL 60065 for safety. |
| EMI/EMC | CE, C-tick, FCC Class B, ICES, VCCI |
| Environmental | Complies with the appropriate requirements of RoHS, WEEE |
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (8.0-050511-D3) |