| XPA 2003C-70V, XPA 2003C-100V |
|
| Audio |
|---|
| Voltage gain | |
| Channels 1 and 2 | 23x (27 dB) |
| Channel 3 | |
| XPA 2003C-70V | 57x (35 dB) |
| XPA 2003C-100V | 81x (38 dB) |
| Crosstalk | 75 dB (typical) @ 1 kHz |
| CMRR | 75 dB (typical) @ 1 kHz |
|
| Audio input |
|---|
| Number/signal type | 3 balanced/unbalanced |
| Connectors | (3) 3.5 mm captive screw connectors, 3 pole |
| Impedance | >10k ohms unbalanced/balanced, DC coupled |
| Nominal level | +4 dBu (1.23 Vrms), balanced |
| Maximum level | +21 dBu (8.69 Vrms), balanced |
| Input sensitivity | +4 dBu (1.23 Vrms) |
| Input signal detection threshold | -40 dBu ±3 dB, balanced |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output |
|---|
| Number/signal type | |
| XPA 2003C-70V | 2 channels, 4 or 8 ohms
1 channel, 70 V |
| XPA 2003C-100V | 2 channels, 4 or 8 ohms
1 channel, 100 V |
| Connectors | (1) 5 mm screw lock captive screw connector, 4 pole
(1) 5 mm screw lock captive screw connector, 2 pole |
| NOTE | These connectors accept wires of 22 AWG to 12 AWG. |
|
| Load impedance | |
| Channel 1 or 2 | 4 ohms minimum |
| Channel 3 | |
| XPA 2003C-70V | 25 ohms minimum |
| XPA 2003C-100V | 50 ohms minimum |
| Amplifier type | Class D |
| Output power | |
| Channel 1 or 2 (8 ohm) | 100 watts rms per channel, 1 kHz, 0.1% THD |
| Channel 1 or 2 (4 ohm) | 200 watts rms per channel, 1 kHz, 0.1% THD |
| Channel 3 | |
| XPA 2003C-70V (70 V output) | 200 watts rms per channel, 70 V, 1 kHz, 0.1% THD |
| XPA 2003C-100V (100 V output) | 200 watts rms per channel, 100 V, 1 kHz, 0.1% THD |
| Frequency response | 20 Hz to 20 kHz, ±1 dB |
| THD + Noise | |
| Channel 1 or 2 | 0.1% @ 20 Hz to 20 kHz, 8 ohms, 3 dB below clipping |
| Channel 3 | 0.1%, 1 kHz, 3 dB below clipping |
| S/N | 100 dB, 20 Hz - 20 kHz, unweighted |
| Damping factor | |
| Channel 1 or 2 | >100 @ 8 ohms |
| Channel 3 | |
| XPA 2003C-70V | >100 @ 25 ohms |
| XPA 2003C-100V | >100 @ 50 ohms |
| High pass filter | |
| XPA 2003C-70V | 80 Hz, 12 dB per octave rolloff for 70 V line output (switch selectable) |
| XPA 2003C-100V | 80 Hz, 12 dB per octave rolloff for 100 V line output (switch selectable) |
|
| Control/remote — amplifier |
|---|
| Control port | (1) 3.5 mm captive screw connector, 2 pole |
| Pin configurations | |
| Standby power control (contact closure) | Pin 1 = GND, pin 2 = standby |
|
| General |
|---|
| Power | Internal
Input: 100-240 VAC, 50-60 Hz |
| Power consumption and thermal dissipation |
XPA 2003C-70V
| |
115 VAC, 60Hz |
230 VAC, 50Hz |
AC Line
Current |
AC Power
Consumed |
Thermal
Dissipation |
AC Line
Current |
AC Power
Consumed |
Thermal
Dissipation/ |
| Condition |
A |
W |
W |
BTU/hr |
A |
W |
W |
BTU/hr |
Active (1/8 power), all
channels driven |
Ch 1 & 2 (8Ω) + Ch 3 (70 V) |
0.8 |
92.2 |
42.2 |
144 |
0.5 |
92.9 |
42.9 |
146 |
| Ch 1 & 2 (4Ω) + Ch 3 (70 V) |
1.1 |
122.4 |
47.4 |
162 |
0.6 |
122.4 |
47.4 |
162 |
| Quiescent (idle) |
0.3 |
28.9 |
28.9 |
99 |
0.2 |
29.8 |
29.8 |
102 |
| Standby |
<0.1 |
<1 |
<1 |
<3 |
<0.1 |
<1 |
<1 |
<3 |
|
XPA 2003C-100V
| |
115 VAC, 60Hz |
230 VAC, 50Hz |
AC Line
Current |
AC Power
Consumed |
Thermal
Dissipation |
AC Line
Current |
AC Power
Consumed |
Thermal
Dissipation/ |
| Condition |
A |
W |
W |
BTU/hr |
A |
W |
W |
BTU/hr |
Active (1/8 power), all
channels driven |
Ch 1 & 2 (8Ω) + Ch 3 (100 V) |
0.8 |
94.4 |
44.4 |
152 |
0.46 |
95.3 |
45.3 |
155 |
| Ch 1 & 2 (4Ω) + Ch 3 (100 V) |
1.1 |
123.1 |
48.1 |
164 |
0.58 |
123.3 |
48.3 |
165 |
| Quiescent (idle) |
0.3 |
28.1 |
28.1 |
96 |
0.17 |
28.6 |
28.6 |
98 |
| Standby |
<0.1 |
<1 |
<1 |
<3 |
<0.1 |
<1 |
<1 |
<3 |
|
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, no vents, with heat sinks on the sides |
| Protection | Clip limiting, thermal, short circuit, DC output |
| Indication | Limiter/Protect LED indicates the onset of clip limiting, thermal cycling, or a short circuit |
| Mounting | |
| Rack mount | Yes, with included mounting brackets |
| Enclosure type | Metal |
| Enclosure dimensions | 1.7" H x 17.4" W* x 12.0" D (1U high, full rack wide)
(4.3 cm H x 44.2 cm W* x 30.5 cm D)
*Width excludes rack ears. 19.0" (48.3 cm) W with rack ears. |
| Product weight | 9.2 lbs (4.2kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | BSMI, CCC, CE, c-UL, GS, KC, PSE, S-Mark, UL
Meets UL 60065, IEC 60065, and BSEN 60065 for AV equipment. |
| EMI/EMC | CE, CISPR 22 Class B, CISPR 24, C-tick, EN55103-1, EN55103-2, FCC Class B, ICES, KCC, VCCI Class B |
| Environmental | Complies with the appropriate requirements of ENERGY STAR® (ENERGY STAR qualified amplifier), EU code of conduct, RoHS, WEEE |
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (5702-D18) |